dma_timer_expiry: dma status == 0x21

When I have both CPU's in my motherboard, I get a lot of errors on IDE drive access. On most boot attempts, the system eventually comes up, but all disk accesses are then super slow (I assume they are being retried multiple times).

When I first installed Linux, I had only one CPU in the motherboard, and I didn't have this problem. The problem started when I put in the second CPU. I tried many google searches for related problems, found lots of those, understood very few of the suggested corrections, tried those and improved nothing. I'm back to just one CPU and the problem seems to be gone.

I'll paste the entire dmesg output later in this post, but here are a few extracts I think are relevant:

BIOS failed to enable PCI standards compliance, fixing this error.
I/O APIC: AMD Errata #22 may be present. In the event of instability try
: booting with the "noapic" option.
After doing some google searches on that, I decided to add noapic to the line in /boot/grub/menu.lst that now reads
kernel /boot/vmlinuz-2.6.18-5-k7 root=/dev/hda1 ro noapic
Was that the correct thing to do for that error? That error message still appears in dmesg even after I rebooted with that change. That error message also appears whether I have one CPU or two. Adding noapic to that line wasn't ignored entirely. There was a message about it during bootup (that went by too fast for me to try to quote accurately) and it changed the output I get from "cat /proc/interrupts". Without noapic most interrupts are on CPU0. But with noapic all interrupts are on CPU0.
The other threads on "AMD Errata #22" seemed to indicate needing more correction than just "noapic" but I didn't nderstand any of the rest. Any suggestions? Of course I'm only guessing that problem even has any connection to my dual CPU IDE problem.

mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
The reason I had one CPU removed when I installed Linux was I thought it was broken, because the BIOS sees two CPUs but Windows sees only one. I think the above lines from dmesg might explain why Windows doesn't see the second CPU. I don't know if it has anything to do with this IDE problem. Both CPUs seem to work fine when in Linux. Just the IDE hard drive doesn't work right with the second CPU present.

With one CPU the output of "cat /proc/interrupts" is below. With two CPUs and noapic, it looked similar to that but with a column of zeros for CPU1.

CPU0
0: 3148258 XT-PIC timer
1: 6685 XT-PIC i8042
2: 0 XT-PIC cascade
5: 0 XT-PIC eth0
8: 1 XT-PIC rtc
9: 1 XT-PIC acpi
10: 739367 XT-PIC aic7xxx, nvidia
11: 18000 XT-PIC aic7xxx, ohci_hcd:usb1, eth1
12: 210825 XT-PIC i8042
14: 21536 XT-PIC ide0
15: 111842 XT-PIC ide1
NMI: 0
LOC: 3148155
ERR: 890
MIS: 0

The full dmesg with 2 CPUs and noapic is
Linux version 2.6.18-5-k7 (Debian 2.6.18.dfsg.1-17) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Dec 24 17:18:11 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff6c00 (ACPI data)
BIOS-e820: 00000000bfff6c00 - 00000000c0000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
2175MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f74c0
On node 0 totalpages: 786416
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 557040 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7460
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0xbfff451b
ACPI: FADT (v001 TYAN GUINNESS 0x06040000 PTEC 0x000f4240) @ 0xbfff6b2e
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0xbfff6ba2
ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:6 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
Detected 1526.532 MHz processor.
Built 1 zonelists. Total pages: 786416
Kernel command line: root=/dev/hda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3111544k/3145664k available (1555k kernel code, 32936k reserved, 579k data, 196k init, 2228160k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3055.33 BogoMIPS (lpj=6110669)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) MP 1800+ stepping 02
SMP alternatives: switching to SMP code
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3053.36 BogoMIPS (lpj=6106724)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) Processor stepping 02
Total of 2 processors activated (6108.69 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=859
checking if image is initramfs... it is
Freeing initrd memory: 4790k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7c0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM1._STA] (Node dfb076a8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM2._STA] (Node dfb075b8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.LPT_._STA] (Node dfb07478), AE_NOT_FOUND
Boot video device is 0000:00:0e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 *10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM1._STA] (Node dfb076a8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM2._STA] (Node dfb075b8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.LPT_._STA] (Node dfb07478), AE_NOT_FOUND
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM1._STA] (Node dfb076a8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.COM2._STA] (Node dfb075b8), AE_NOT_FOUND
ACPI Error (psargs-0355): [Z00Q] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.ISA_.SIO_.LPT_._STA] (Node dfb07478), AE_NOT_FOUND
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
PCI: Failed to allocate mem resource #6:10000@fa000000 for 0000:01:05.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ea000000-eaffffff
PREFETCH window: f8000000-f9ffffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1198937048.344:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
BIOS failed to enable PCI standards compliance, fixing this error.
I/O APIC: AMD Errata #22 may be present. In the event of instability try
: booting with the "noapic" option.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: acpi_pm clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD7411: IDE controller at PCI slot 0000:00:07.1
AMD7411: chipset revision 1
AMD7411: not 100% native mode: will probe irqs later
AMD7411: 0000:00:07.1 (rev 01) UDMA100 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI subsystem initialized
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
hda: WDC WD400BB-00AUA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-W524E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 169
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0f.0: 3Com PCI 3c980C Python-T at f8838000.
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 19 (level, low) -> IRQ 177
0000:00:10.0: 3Com PCI 3c980C Python-T at f8898400.
ACPI: PCI Interrupt 0000:00:07.4[D] -> GSI 19 (level, low) -> IRQ 177
ohci_hcd 0000:00:07.4: OHCI Host Controller
ohci_hcd 0000:00:07.4: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:07.4: irq 177, io mem 0x000dc000
hda: max request size: 128KiB
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 <<6>ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 185
hda5 >
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 1404kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0

aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

ACPI: PCI Interrupt 0000:00:0d.1[B] -> GSI 17 (level, low) -> IRQ 193
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0

aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs

hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: DMA disabled
ide0: reset timed-out, status=0xd0
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156223, sector=78156221
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156221
Buffer I/O error on device hda5, logical block 1646629
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156224, sector=78156223
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156223
Buffer I/O error on device hda5, logical block 1646630
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78155963, sector=78155963
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78155963
Buffer I/O error on device hda5, logical block 1646500
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156213, sector=78156211
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156211
Buffer I/O error on device hda5, logical block 1646624
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156213, sector=78156213
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156213
Buffer I/O error on device hda5, logical block 1646625
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78165122, sector=78165120
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78165120
Buffer I/O error on device hda, logical block 9770640
input: PC Speaker as /class/input/input1
EDAC MC: Ver: 2.0.1 Dec 24 2007
EDAC MC0: Giving out device to amd76x_edac AMD762: DEV 0000:00:00.0
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78165120, sector=78165120
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78165120
Buffer I/O error on device hda, logical block 9770640
Real Time Clock Driver v1.12ac
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78165298, sector=78165296
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78165296
Buffer I/O error on device hda, logical block 9770662
ts: Compaq touchscreen protocol output
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78165300, sector=78165296
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78165296
Buffer I/O error on device hda, logical block 9770662
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: HPC vendor_id 1022 device_id 700d ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
floppy0: no floppy controllers found
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156021, sector=78156019
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156019
Buffer I/O error on device hda5, logical block 411632
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156158, sector=78156155
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156155
Buffer I/O error on device hda5, logical block 411649
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156157, sector=78156155
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156155
Buffer I/O error on device hda5, logical block 411649
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156214, sector=78156211
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156211
Buffer I/O error on device hda5, logical block 411656
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156211, sector=78156211
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156211
Buffer I/O error on device hda5, logical block 411656
Adding 1646620k swap on /dev/hda5. Priority:-1 extents:1 across:1646620k
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
eth1: setting full-duplex.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
ACPI: Power Button (CM) [PWRB]
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
ppdev: user-space parallel port driver
eth1: no IPv6 routers present
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=78156162, sector=78156155
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 78156155
Buffer I/O error on device hda5, logical block 411649
eth0: setting half-duplex.
ADDRCONF(NETDEV_UP): eth0: link is not ready
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 193
NVRM: loading NVIDIA Linux x86 Kernel Module 71.86.01 Wed Sep 5 20:14:16 PDT 2007
eth1: no IPv6 routers present